VapCap OmniVap is an amazing portable vaporizer, one of the best models of the legendary vaporizer from DynaVap. Apart from a rapid heating (on-demand vaporization), a powerful vapor and huge efficiency – features you’ll find in all the VapCaP devices – it also stands out due to a unique regulation system of air flow inside the device, which lets the user modify the thickness and the strength of the vapor.
››› Are you about to buy a vaporizer? Buy VapCap OmniVap Vaporizer in the authorized VapeFully store.
VapCap OmniVap Vaporizer – preparation
VapCap OmniVap Vaporizer has no battery so you don’t need to worry about charging it before the first use. There’s no need to do the burn-off with an empty chamber, either. Before you start vaping, you have to grind the herbs and place them in the heating chamber. OmniVap does equally well with any herbs consistency but we’d say it’s better not grind them too finely as some tiny particles might get into the condenser and the user’s mouth. The best solution is to use medium-ground herbs and to squeeze them gently once loaded into the chamber. The results of our tests show that it’s best to use the so-called vacuum method – suck the herbs into the chamber and squeeze them gently with a finger. If you squeeze the herbs too much, you will block the air circulation inside the chamber, which will make the inhalation more difficult.
Just like every VapCap, OmniVap needs an external source of heat to heat the herbs. The best option is to use a jet-flame lighter or a butane mini-lighter. Even though other types of flame (e.g. one from a regular lighter) theoretically are also good for heating the cap of OmniVap, it will last longer when you use it and a regular flame will leave soot marks on the cap. A jet-flame lighter is a faster and cleaner solution. It doesn’t matter what kind of gas you use in a lighter because when you use OmniVap, the fumes from the gas are not inhaled so you can easily use the cheapest gas for lighters.
How to use the vaporizer?
When the chamber is full, you need to place the steel cap on the heating chamber and start to heat it with a jet-flame lighter. You can get different results, depending on where you direct the flame – the farther it will be from the tip of the cap, the higher the temperature will be.
NOTE: Never heat the tip of the cap with a flame as it may lead to overheating and permanent damage to the cap!
Once the device reaches the appropriate temperature, the cap will make a characteristic, double click. This is when you can start the inhalation. What makes VapCap OmniVap different from other VapCap models is the possibility to regulate the density and power of the vapor – you can do it by turning the mouthpiece. When you turn the mouthpiece, you can adjust the vapor parameters to your individual needs. You can get strong and dense vapor or you can choose to enjoy a gentle steam. You can set the mouthpiece in a position that guarantees the best vapor for you or you can try various settings during the inhalation. After a few draws, the cap will click again, which means that the temperature has dropped below the optimum level and you have to reheat the cap again. In order to fully use the content of the chamber, you need 2 to 4 such heating cycles, depending on the type of the material you use.
Even though VapCap OmniVap has a “clutch”, you need to make sure you don’t cover it during the inhalation as it allows for the air to get into the device. The thickness of the vapor is regulated only by turning the mouthpiece.
How to clean VapCap OmniVap Vaporizer?
VapCap OmniVap doesn’t require frequent cleaning. If you want to do a deep cleaning of your vaporizer, you have to disassemble the device completely. Remove all the gaskets (make sure they don’t come in contact with isopropyl alcohol, just like the cap of the heating chamber) and put them aside. If you have the Titanium model, you can soak all the elements, except for the gaskets, in isopropyl alcohol. Then, rinse them well with hot water and leave them to dry completely. If you have the Carbon model, soak all the elements except for the gaskets and the carbon fiber lining. All the parts that cannot be cleaned with isopropyl alcohol, can be cleaned with warm water and washing up liquid. When all the elements dry out, you can reassemble your OmniVap.
We recommend THCleaner for VapCap OmniVap Vaporizer cleaning.
Have we missed any tips? Let us know which ones you found the most useful!